{"product_id":"bambu-lab-textured-pei-plate-256-mm","title":"Bambu Lab Textured PEI Plate 256 mm • P2S, X2D, P1, X1, A1","description":"\u003cp\u003eFits these printers: Bambu Lab P2S, X2D, P1S, P1P, X1C, X1E and A1. Size: 256 x 256 mm.\u003c\/p\u003e\u003cp\u003eThis is the 1st gen plate. Bambu makes the 256 mm Textured PEI Plate in two generations. Both are the same size. The only change is the QR code that the printer reads.\u003c\/p\u003e\u003cp\u003eFits fully: A1, P1S, P1P, X1C and X1E. These printers use the 1st gen plate with no extra steps.\u003c\/p\u003e\u003cp\u003eP2S and X2D: the plate fits and prints well. These printers read the plate type from the QR code, and they can not read the 1st gen code. If you see \"Build plate not recognized\", tap \"Resolved\" on the screen, or turn off Build Plate Detection in the settings.\u003c\/p\u003e\u003cp\u003ePrints grab hold on the first layer, then pop right off once the plate cools. The textured PEI gives the bottom of every print a rough, matte finish. Most filaments need no glue.\u003c\/p\u003e\u003ch3\u003eWhat's Included\u003c\/h3\u003e\u003cul\u003e\u003cli\u003e1 x Bambu Lab Textured PEI Plate, 256 x 256 mm (1st gen)\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSurface: textured PEI powder coat, 0.075 mm\u003c\/li\u003e\n\u003cli\u003eBase: magnetic spring steel, 0.5 mm\u003c\/li\u003e\n\u003cli\u003eHeat limit: up to 180°C\u003c\/li\u003e\n\u003cli\u003ePrint area: 256 x 256 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBed Temps\u003c\/h3\u003e\u003cp\u003eThese are Bambu Lab's starting points. Tune them for your model and filament.\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eFilament\u003c\/th\u003e\n\u003cth\u003eBed temp\u003c\/th\u003e\n\u003cth\u003eGlue?\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePLA, PLA-CF, PLA-GF\u003c\/td\u003e\n\u003ctd\u003e45 to 60°C\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePETG, PETG-CF\u003c\/td\u003e\n\u003ctd\u003e60 to 80°C\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTPU\u003c\/td\u003e\n\u003ctd\u003e35 to 45°C\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePVA\u003c\/td\u003e\n\u003ctd\u003e45 to 60°C\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eABS, ASA\u003c\/td\u003e\n\u003ctd\u003e90 to 100°C\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePET-CF\u003c\/td\u003e\n\u003ctd\u003e80 to 100°C\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePC, PC-CF\u003c\/td\u003e\n\u003ctd\u003e90 to 110°C\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePA, PA-CF, PAHT-CF\u003c\/td\u003e\n\u003ctd\u003e90 to 110°C\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch3\u003eGood To Know\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWait until the bed is 35°C or cooler. If a print still sticks, flex the steel plate and it pops off.\u003c\/li\u003e\n\u003cli\u003eA hotter bed gives more grip.\u003c\/li\u003e\n\u003cli\u003eLightly sand with 600 grit paper to bring back lost grip.\u003c\/li\u003e\n\u003cli\u003eThe nozzle wipe area wears over time. That is normal and does not hurt print quality.\u003c\/li\u003e\n\u003cli\u003eWash the plate with dish soap and warm water to keep the grip strong. Dust and skin oil cut grip.\u003c\/li\u003e\n\u003cli\u003eNever clean it with acetone. It hurts the PEI.\u003c\/li\u003e\n\u003cli\u003eLet the plate cool for a few minutes before you take your print off.\u003c\/li\u003e\n\u003cli\u003eUse only Bambu Lab glue on Bambu Lab plates.\u003c\/li\u003e\n\u003cli\u003eThis plate wears out over time. The warranty covers defects on arrival, not scratches or dents from use.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood For\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eEveryday PLA and PETG prints\u003c\/li\u003e\n\u003cli\u003eParts that need a grippy first layer\u003c\/li\u003e\n\u003cli\u003eHigh temp filaments like ABS, ASA, PC and nylon\u003c\/li\u003e\n\u003cli\u003eA matte, textured bottom face\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Bambu Lab","offers":[{"title":"Textured PEI Plate 256 mm, 1st gen","offer_id":69148110258419,"sku":"FAP007","price":36.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0279\/4541\/files\/up_t2.jpg?v=1794859166","url":"https:\/\/www.reprapwarehouse.com\/products\/bambu-lab-textured-pei-plate-256-mm","provider":"RepRap Warehouse","version":"1.0","type":"link"}